**From:** Jérôme Hénin (*jerome.henin_at_ibpc.fr*)

**Date:** Wed Nov 11 2020 - 13:53:36 CST

**Next message:**Abhishek Acharya: "Re: Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Previous message:**Abhishek Acharya: "Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**In reply to:**Abhishek Acharya: "Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Next in thread:**Abhishek Acharya: "Re: Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Reply:**Abhishek Acharya: "Re: Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Messages sorted by:**[ date ] [ thread ] [ subject ] [ author ] [ attachment ]

Hello Abhishek,

you're almost there, but it's simpler than you think. If you can collect the joint histogram P(z1, z2), biased along z1, then you can obtain the 2d PMF by reweighting using the 1d CZAR PMF:

A(z1, z2) = -kT ln( P(z1, z2) / P(z1) ) + A_CZAR(z1)

where P(z1) is the observed (biased) histogram in z1 (aka the z1 marginal of the 2d histogram).

Best,

Jerome

----- On 11 Nov 20, at 20:04, Abhishek Acharya abhi117acharya_at_gmail.com wrote:

*> Hello,
*

*>
*

*> We are trying to run 1D eABF simulations on our system of interest.
*

*> Specifically, the simulation is divided into 3 windows and we use 5 walkers
*

*> per window for sampling.
*

*>
*

*> Obtaining the 1D PMF looks straightforward to do. Just to be sure we,
*

*> 1) Combine data for walkers using the inputPrefix directive of ABF to get
*

*> combined outputs for each window.
*

*> 2) Combine the gradients for each window to obtain the full gradient,
*

*> taking care of the edge values.
*

*> 3) Integrate the gradient to obtain 1D PMF.
*

*>
*

*> However for better insights and comparison with methods used previously, we
*

*> would like to obtain a PMF projected along an additional CV to obtain a 2D
*

*> picture. So, the idea is to apply ABF bias along, say z1 CV, but also
*

*> obtain samples along z2 (unbiased and defined without the Extended
*

*> Largrangian directive) and somehow combine these to obtain the 2D PMF.
*

*> Naively, I thought that maybe we can do a post-hoc estimation using the
*

*> CZAR estimator; essentially obtain the biased 2D histogram, P(z1, z2) and
*

*> the z1-averaged forces from the CV values and total forces printed out to
*

*> the colvar traj file, and finally using the 1D CZAR expression to obtain
*

*> the 2D PMF.
*

*>
*

*> 1. Is this at all a correct strategy? If not, some hints would be helpful.
*

*>
*

*> 2. Fu et al, *J. Chem. Theory Comput.* 2016 indicates that accurate
*

*> post-hoc analysis would require printing out the CV and force values every
*

*> timestep. For the aforesaid procedure, I thought that maybe we can use the
*

*> histogram directive to obtain the final 2D counts and combine it with the
*

*> 1D averaged forces.
*

*>
*

*> Any suggestions would be highly appreciated.
*

*>
*

*> Thanks in advance.
*

*>
*

*> Sincerely,
*

*> Abhishek Acharya
*

**Next message:**Abhishek Acharya: "Re: Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Previous message:**Abhishek Acharya: "Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**In reply to:**Abhishek Acharya: "Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Next in thread:**Abhishek Acharya: "Re: Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Reply:**Abhishek Acharya: "Re: Calculating 2D PMF from 1D eABF simulations using CZAR estimator."**Messages sorted by:**[ date ] [ thread ] [ subject ] [ author ] [ attachment ]

*
This archive was generated by hypermail 2.1.6
: Fri Dec 31 2021 - 23:17:10 CST
*