Re: high pressure

From: Tillmann Utesch (tillmann.utesch_at_mail.tu-berlin.de)
Date: Thu Mar 11 2010 - 15:05:59 CST

Hello Giacomo,

Thanks for your help.
I will try both proposals
a) NVT enesemble
b) very strong position restraints instead of fixed atoms

Best regards,
Tillmann
  ----- Original Message -----
  From: Giacomo Fiorin
  To: Tillmann Utesch
  Cc: Dimitar V Pachov ; namd-l_at_ks.uiuc.edu
  Sent: Thursday, March 11, 2010 8:00 PM
  Subject: Re: namd-l: high pressure

  Hi Tillmann, as Dimitar suggested, you can keep the NPT ensemble, by using harmonic position restraints. If you also set their force constants to reproduce the expected fluctuations in the gold lattice, it actually improves the physical description a whole lot.

  In general, and not only regarding temperature and pressure coupling, it's always better to use harmonic restraints as opposed to fixed atoms, unless you have a particular reason to keep those positions constant up to the last digit.

  Giacomo

  ---- ----
  Giacomo Fiorin
    ICMS - Institute for Computational Molecular Science
      Temple University
      1900 N 12 th Street, Philadelphia, PA 19122
  work phone: (+1)-215-204-4216
  mobile: (+1)-267-324-7676
  mail: giacomo.fiorin_at_gmail.com
  ---- ----

  On Thu, Mar 11, 2010 at 11:29 AM, Tillmann Utesch <tillmann.utesch_at_mail.tu-berlin.de> wrote:

    Hi Dimitar,

    Thanks for the quick reply.

    I used a fixed gold layer, because I don't have bonding parameters for gold atoms. I have heard of problems of fixed atoms and an NPT enesemble
    and tried to solve the discrepancy by excluding the surface from pressure calculations (without changing the pressure problem).
    The observed pressure fluctuations after a 2 ns long run are around 2050 bar (+- 150 bar). If I decrease the charge density, the average value moves to lower pressure,
    so I think it is a special problem with high immobile charge densities.
    In all simulations, I set the LangevinPistonTarget to 1 athmosphere, but I did not reach a fluctuation around this target.

    Another point is that introduction of ions into the system leads to pressure fluctuations around the desired value of 1 athmosphere after equilibration of the ions.

    I will try a NVT ensemble now and hope it will solve the problem.

    Best regards,
    Tillmann

    ----- Original Message ----- From: "Dimitar V Pachov" <dpachov_at_brandeis.edu>
    To: "tillmann utesch" <tillmann.utesch_at_mail.tu-berlin.de>
    Cc: <namd-l_at_ks.uiuc.edu>
    Sent: Thursday, March 11, 2010 4:09 PM
    Subject: Re: namd-l: high pressure

      ----- "tillmann utesch" <tillmann.utesch_at_mail.tu-berlin.de> wrote:

      | From: "tillmann utesch" <tillmann.utesch_at_mail.tu-berlin.de>
      | To: namd-l_at_ks.uiuc.edu
      | Sent: Thursday, March 11, 2010 7:01:06 AM GMT -05:00 US/Canada Eastern
      | Subject: namd-l: high pressure
      |
      | Hi all,
      |
      | I run a NPT simulation of an enzyme on a SAM coated gold surface.
      | During the simulation all gold atoms were fixed to their positions.

      It is not a good idea at all to run NPT with any positional constraints. Pressure is controlled by volume scaling. Fixed coordinates introduce artifacts and certain frequency wave propagation/fluctuations that are not desired. You cannot say that your system samples appropriately the equilibrium NPT ensemble in that case.

      | The total system is neutrally charged, but the head-groups of the
      | monolayers are positively and the gold atoms are negatively charged.
      |
      | So the charges are not able (gold) or limited (SAM) in moving.
      | The simulations are very stable, but the the pressure is fluctuating
      |
      | around a very high value.

      What is "very high"? How large are the fluctuations? Instantaneous pressure tends to fluctuate a lot, but your average should be around the externally specified value.

      | For the pressure control I used the Langevin
      |
      | piston method. Forces between fixed atoms were ignored and for the
      | electrostatic interactions I used the PME summation.
      | Exclusion of gold and SAM atoms of the pressure calculations did not
      |
      | change the very high pressure in the system.
      | What shall I do now? Is the high pressure a result of the high charge
      |
      | density in the SAM and the gold? How can a modify my system to get
      | normal pressure values?

      What is "normal"?
      I do not know why you want to fix the gold atoms, but it would be much better (but not prefect) to put (small) positional harmonic restraints which will allow at least some spacial degrees of freedom. Or you could try NVT.

      Dimitar

      |
      | Thanks,
      | Tillmann
      |
      | -- | Tillmann Utesch
      | Institut für Chemie, Max-Volmer-Laboratorium
      | TU Berlin, PC 14
      | Straße des 17. Juni 135
      | D-10623 Berlin
      | Tel. +49-(0)30-314-26389

      --
      ========================================================
      Dimitar V Pachov

      PhD Candidate
      Physics & Biochemistry Department Phone: (781) 736-2326
      Brandeis University, MS 057 Email: dpachov_at_brandeis.edu
      ========================================================

This archive was generated by hypermail 2.1.6 : Wed Feb 29 2012 - 15:55:33 CST