From: Norman Geist (norman.geist_at_uni-greifswald.de)
Date: Mon Nov 11 2013 - 03:26:06 CST
Read something about „Intel HT-Hyperthreading“.
Yes.
Norman Geist.
Von: owner-namd-l_at_ks.uiuc.edu [mailto:owner-namd-l_at_ks.uiuc.edu] Im Auftrag von James Starlight
Gesendet: Montag, 11. November 2013 09:49
An: Norman Geist; Namd Mailing List
Betreff: Re: namd-l: Two GPU-based workstation
2) about cores
so If my physical number is 6 ( I dont really know why debian recognize 12 cores)
I should use +p6 +ppn3 +devices 0,1 do adjust each 3 cores for each gpu shouldn't it ?
2013/11/11 James Starlight <jmsstarlight_at_gmail.com>
Norman,
using
pmegridspacing 1;
fullElectFrequency 2;
instead of
PMEGridSizeX $fftx; # should be close to the cell size
PMEGridSizeY $ffty; # corresponds to the charmm input fftx/y/z
PMEGridSizeZ $fftz;
pmegridspacing 1;
have crashed my simulation at the beginning
namd2 +idlepoll +p12 +ppn6 +devices 0,1 ./aMD.conf >> b2ar_p0gDiheBoostlog_20000
------------- Processor 0 Exiting: Called CmiAbort ------------
Reason: FATAL ERROR: Periodic cell has become too small for original patch grid!
Possible solutions are to restart from a recent checkpoint,
increase margin, or disable useFlexibleCell for liquid simulation.
(this time I've start from the checkpoint of the previous run, performed with the defined XYZ of the PME. Does it means that I should to begin simulation from the beginning of the equilibration phase with fullElectFrequency >1 or there are alternative solutions?
James
2013/11/11 Norman Geist <norman.geist_at_uni-greifswald.de>
Why not simply setting „pmegridspacing 1“?
I usually use numcpus/numgpus for each gpu. And really believe me, you only got 6 cores not 12. And running 2 simulations on only one cpu socket is inefficient.
Norman Geist.
Von: owner-namd-l_at_ks.uiuc.edu [mailto:owner-namd-l_at_ks.uiuc.edu] Im Auftrag von James Starlight
Gesendet: Samstag, 9. November 2013 15:53
An: Namd Mailing List
Betreff: Re: namd-l: Two GPU-based workstation
by the way increasing of the fullElectFrequency > 1 has end simulation with the errors about unproperly set XYZ of the PME boundaries ( with fullElectFrequency 1 I use 80 80 120 simulating membrane protein and have not any errors. How could I change pme options ?
also my question is the optimal balancing of the number of CPUs for each GPU. Is there some impirical relationships showing what amount of CPUs is needed for each GPU ?
assuming that I obtained best performance using
namd2 +idlepoll +p12 +devices 0 ./aMD.conf
I'd like to share some CPUs between both available GPUs for the 2 parallel simulations.
James
2013/11/8 James Starlight <jmsstarlight_at_gmail.com>
Could fullelectfrequency 4 increase performance exactly dual-gpu regime ?
In case of running two simulations will it be enough to provide each gpu with the 6 cores ? ( I suppose that I have not obtain good performance in 2 gpu regime exactly due to small number of cores for each gpu)
James
2013/11/7 Ajasja Ljubetič <ajasja.ljubetic_at_gmail.com>
On 7 November 2013 06:32, James Starlight <jmsstarlight_at_gmail.com> wrote:
I've gone to conclusion that using 2 GPUs simultaneously gave me the same performance as 1 GPU like
Yes, this is expected, for such small systems there is too little work at each step to scale efficiently. You can however run one (or two or three) independent simulations on each GPU.
Regards,
Ajasja
This archive was generated by hypermail 2.1.6 : Tue Dec 31 2013 - 23:23:58 CST